common mode filter ? w5f series note: specifications subject to change w ithout notice. please check our we bsite for latest information. proprietary and confidential document of superworld 06/12/2017 p1 d a e c d b 1. part no. expression: w 5 f 9 0 0 - r j ? 1 0 (a) (b)(c) (d) (e)(f) (g) (a) series code (e) packaging code (b) dimension code (f) current rating code (c) material code (g) internal controlled number (d) impedance code 2. configuration & dimensions: unit: mm 3. schematic: a b c d1 d2 e l g1 g2 h 3.20.2 2.50.2 2.20.2 0.80.1 0.9 0.1 0.150.1 4.4 ref. 1.6 ref. 0.6 ref. 3.5 ref. l h g1 g2 4 3 2 1 recommended pcb layout
common mode filter ? w5f series note: specifications subject to change w ithout notice. please check our we bsite for latest information. proprietary and confidential document of superworld 06/12/2017 p2 4. material list: (a) core (b) wire (c) terminal (d) upper plate 5. general specification: (a) operating temp. : -40c to +125c( including self - temperature rise) (b) storage temp. : -40c to +125c (on board) (c) humidity range: 85 2% rh (d) storage condition (component in its packaging) i) temperature: less than 40c ii) humidity : 60% rh 6. electrical characteristics: part number common mode impedance ( ? ) 25% test frequency (mhz) dcr ( ? ) max. rated current (ma) max. rated volt (vdc) max. withstand volt (vdc) max. ir ( ? ) min. w5f900-rj-10 90 100 0.05 1000 50 125 10m w5f601-rj-10 600 100 0.20 1000 50 125 10m W5F102-RD-10 1000 100 0.30 400 50 125 10m
common mode filter ? w5f series note: specifications subject to change w ithout notice. please check our we bsite for latest information. proprietary and confidential document of superworld 06/12/2017 p3 7. characteristics curves: 1101001000 frequency(mhz) 0.1 1 10 100 1000 impedance(ohm) common mode normal mode 1 10 100 1000 10000 frequency(mhz) 0.1 1 10 100 1000 10000 impedance(ohm) common mode normal mode 1 10 100 1000 10000 frequency(mhz) 0.1 1 10 100 1000 10000 impedance(ohm) common mode normal mode W5F102-RD-10 w5f900-rj-10 w5f601-rj-10
common mode filter ? w5f series note: specifications subject to change w ithout notice. please check our we bsite for latest information. proprietary and confidential document of superworld 06/12/2017 p4 8. soldering: mildly activated rosin fluxes are preferred. our terminations are suitable for all re-flow soldering systems. if hand soldering cannot be avoi ded, the preferred technique is the ut ilization of hot air soldering tools. 8-1 solder re-flow recommended temperature profiles for re-flow soldering in figure 1. 8-2 soldering iron (figure 2) products attachment with soldering iron is discouraged due to the inherent process control limitations. in the event that a soldering iron must be employ ed the following precautions are recommended. note : a) preheat circuit and products to 150c. b) 355c tip temperature (max.) c) never contact the ceramic with the iron tip d) 1.0mm tip diameter (max.) e) use a 20 watt soldering iron with tip diameter of 1.0mm f) limit soldering time to 4~5 sec. figure 2. : iron soldering time 1 times max figure 1. : re-flow soldering time 3 times max
common mode filter ? w5f series note: specifications subject to change w ithout notice. please check our we bsite for latest information. proprietary and confidential document of superworld 06/12/2017 p5 9. packaging information: 9-1 reel dimension 9-2 tape dimension 9-3 packaging quantity chip size w5f chip/reel 2,000 inner box 10,000 middle box 50,000 carton 100,000 type a(mm) b(mm) c(mm) d(mm) 7?x8mm 9.00.5 60.0 2.0 13.50.5 178.02.0 size p(mm) po(mm) p2(mm) bo(mm) ao(mm) ko(mm) w(mm) t(mm) w5f 4.00 0.10 4.00 0.10 2.00 0.05 3.65 0.10 2.88 0.10 2.50 0.10 8.00 0.10 0.26 0.05
common mode filter ? w5f series note: specifications subject to change w ithout notice. please check our we bsite for latest information. proprietary and confidential document of superworld 06/12/2017 p6 9-4 tearing off force application notice: 1. storage conditions: to maintain the solderability of terminal electrodes: a) recommended products should be used wi thin 12 months from the time of delivery. b) the packaging material should be kept wh ere no chlorine or sulfur exists in the air. 2. transportation: a) products should be handled with care to avoi d damage or contamination from perspiration and skin oils. b) vacuum pick up is strongly recommended for individual components. c) bulk handling should ensure that abrasion and mechanical shock are minimized. the force for tearing off cover tape is 15 to 80 grams in the arrow direction under the following conditions. room temp. ( ) room humidity (%) room atm (hpa) tearing speed mm/min 5~35 45~85 860~1060 300
|
